BLUE SKY - SYSTEM ONE 2.1 STUDIO MONITOR

€ 2.100,00

Sistema 2.1 Blue Sky composto da subwoofer 12" e satelliti SAT 6.5 MK II

Sky System One is the original manifestation of Blue Sky’s unique approach to accurate, full-range monitoring. Each 100-Watt bi-amplified SAT 6.5 MK II satellite speaker employs a 6.5" hemispherical driver and 1" Neodymium tweeter with a dual concentric diaphragm and integral wave guide. Bass management and level control are incorporated within the SUB 12 subwoofer which features a single long excursion 12" woofer and a 200-Watt, low distortion power amplifier.

SUB 12 - 12” Active Subwoofer

Voltage Sensitivity 90dB SPL @ 100mv @ 1M
(40 to 80Hz bandwidth limited
pink noise)
Frequency Response (anechoic) 30 to 200Hz +/-3dB
Typical In-Room Response 20 to 200Hz (3000 Cubic Feet)
Bass Management Section
Input Impedance 20k Ohms balanced
Common Mode Rejection Ratio 40dB typical @60Hz
Maximum Input Level (all inputs) +24dBu balanced
Maximum Output Level +24dBu balanced
Output Impedance 200 Ohms balanced
Auto Mute Time Out >15 Minutes
Mute Threshold (all inputs) 30mV
Left &Right Inputs to Sat Outputs
Gain (balanced in and out) 0dB
High-Pass Filter type 2nd order Linkwitz-Riley
High-Pass Filter Cutoff 80Hz
High-pass Filter Q .707
THD + Noise .002% @ 1kHz @ +4dBu
Left & Right Inputs to Sub Out
Gain 0dB
Low-Pass Filter Type 4th order Linkwitz-Riley
Low-Pass Cutoff 80Hz
Subwoofer Direct In to Direct Output
Gain 0dB
Low-Pass Filter None

Enclosure
* Solid 3/4” MDF construction with 1” MDF Front and Rear Baffl e
* Viscoelastic energy absorbing front baffl e coating
* Flush mounted driver
* Isolation feet are included. Inserts for optional attachment of spike
feet.
* Dimensions are 18” H x 16” W x 20” D (22.07” with heatsink and
grill)
* Weight 62lbs.
12” Woofer
* Long excursion design with cast aluminum frame.
* 2” voice coil with vented motor for high power handling
* Fully video shielded
Subwoofer Amplifi er
* Discrete symmetrical bipolar design with localized feedback
* 200-W RMS into 4 Ohms
* THD + Noise less than 0.015% at rated power @100Hz
* Adjustable gain control


SAT 6.5 MK II Specifications

Sealed Enclosure
Solid .75” MDF with 1” front / rear baffle and internal bracing
Viscoelastic engergy absorbing front baffle coating
.25” x 20 inserts for attachment of Omnimount type 60 brackets
Dimensions (H x W x L):
12” x 8” x 11.88” (includes heatsink and tweeter wave guide)*
*For complete dimensions see page 14 [SAT 6.5 MK II Cabinet Dimensions].
Weight: 28.5 lbs.
1” Tweeter
Dual concentric diaphragm with integral wave-guide
High-power ferrite motor structure
Full video shielded
6.5” Hemispherical Woofer
6.5” high excursion woofer with vented motor
Cast aluminum frame
1.5” Aluminum voice coil
Copper shorting ring for lower distortion
Ultra low power compression design
Mica filled polypropylene cone w/ Rubber surround
Fully video shielded
Amplifiers & Electronics
Discrete symmetrical bipolar design with localized feedback
100-Watts* into 4-Ohm (6.5” woofer)
.01% THD + noise at rated power @ 1 kHz
100-Watts* into 4-Ohm (Tweeter)
.01% THD + noise at rated power @ 1 kHz
*Power is limited by protection circuitry.
XLR electronically balanced input
Fixed and Adjustable gain controls
B00® optimized crossover
Input impedance: 10K balanced
Common Mode Rejection 40dB typical @ 60Hz
Voltage Sensitivity (high gain) 200mv=90dB SPL @ 1 meter
Maximum Input Level: +24dBu balanced
Frequency Response: +/- 3dB 80Hz to 30kHz
+/-1.5dB 200Hz to 15kHz
Low Frequency Cutoff -3dB @ 80Hz
Internal Crossover Points 1.5kHz
On axis frequency response. Measured at 2
meters, corrected to 1 meter.